Laser igniters could replace spark plugs some day
Results 1 to 6 of 6

Thread: Laser igniters could replace spark plugs some day

  1. #1
    Fuh-coffee we will go Array carbonfibrerocket's Avatar
    Join Date
    Jul 2006
    Hong Ko-quitlam
    08 GSX1300BK, 03 XR650R

    Laser igniters could replace spark plugs some day

    Internal combustion engines are likely to remain in widespread use for some time yet, but it's possible that we may be bidding adieu to that most iconic of engine parts, the spark plug. Researchers from Japan's National Institutes of Natural Sciences (NINS) are creating laser igniters that could one day replace spark plugs in automobile engines. Not only would these lasers allow for better performance and fuel economy, but cars using them would also create less harmful emissions.

    Located at the top of each engine cylinder, spark plugs send a high-voltage electrical spark across a gap between their two metal electrodes. That spark ignites the compressed air-fuel mixture in the cylinder, causing a controlled mini-explosion that pushes the piston down.

    One byproduct of the process are toxic nitrogen oxides (NOx), which pollute the air causing smog and acid rain. Engines would produce less NOx if they burnt more air and less fuel, but they would require the plugs to produce higher-energy sparks in order to do so. While this is technically possible, the voltages involved would burn out the electrodes quite quickly. Laser igniters on the other hand, could ignite leaner mixtures without self-destructing because they don't have electrodes.

    The NINS scientists also address another limitation of spark plugs – the fact that they only ignite the area of the air-fuel mixture closest to them (the top), with much of the heat of the explosion being absorbed by the metal cylinder walls before it can reach down to the piston. Lasers, by contrast, could focus their beams into the middle of the column, from which point the explosion would expand more symmetrically – and reportedly up to three times faster than one triggered by a spark plug.

    Additionally, engine timing could be improved, as lasers can pulse within nanoseconds, while spark plugs require milliseconds.

    In order to cause the desired combustion, a laser would have to be able to focus light to approximately 100 gigawatts per square centimeter with short pulses of more than 10 millijoules each. Previously, that sort of performance could only be achieved by large, inefficient, relatively unstable lasers. The Japanese researchers, however, have created a small, robust and efficient laser that can do the job. They did so by heating ceramic powders, fusing them into optically-transparent solids, then embedding them with metal ions in order to tune their properties.

    Made from two bonded yttrium-aluminum-gallium segments, the laser igniter is just 9 millimeters wide and 11 millimeters long. It has two beams, which can produce a faster, more uniform explosion than one by igniting the air-fuel column in two locations at once – the team is even looking at producing a laser with three beams. While it cannot cause combustion with just one pulse, it can do so using several 800-picosecond-long pulses.

    So far, the laser-ignition system hasn't been installed in an actual automobile. The scientists are reportedly in negotiations with a large spark plug manufacturer and with global auto components manufacturer DENSO Corporation.

    In the meantime, drivers wishing an upgrade from their "old school" spark plugs might be interested in Pulse Plugs, which reportedly boost engine efficiency and performance by storing ignition energy, then discharging it in the form of intense plasma balls.

    The NINS research will be presented next month at the Conference on Lasers and Electro Optics, in Baltimore.
    Quote Originally Posted by bottomfeeder View Post
    Big shitty balls of shit, that's a bastard coated bastard with bastard filling

  2. #2
    Registered User Array spenny's Avatar
    Join Date
    May 2008
    HD XR1200
    I dont think the "benefits" of a lazerplug are cost effective.

  3. #3
    Is it winter yet ? Array SidewaysInto3rd's Avatar
    Join Date
    Jun 2010
    93 Kat 750
    About time I get some freaking laser beams in my freaking car

  4. #4
    Registered User Array
    Join Date
    Jul 2009
    Still working on it...
    Quote Originally Posted by spenny View Post
    I dont think the "benefits" of a lazerplug are cost effective.
    Give it a few years. As technology is shown to be more promising, they'll get more people focusing on bringing production costs down. Interesting idea for sure, definitely something I'll be doing a little more research on to see how feasible it is.

  5. #5
    Registered User Array 4wheelsLESS's Avatar
    Join Date
    Apr 2010
    The Moment
    Only U see my ride
    The timing factor of using laser is a big advantage. As to the cost, it will be cheap if there is enough demand for it. Eventhough a different grade, the current laser pointers now cost about 50 cents to produce as they can be bought retail for about $2. I like it.

    Not knowing the technical details of how this thing works, I am curious about how they get around making it transparent from the beam firing source one it is inside the engine. Burning fuel does have at least some buildup that could block the beam?

  6. #6

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts